Dry your waders to avoid mildew damage

You’ve probably read or heard recommendations to dry your waders out in between uses. You might be wondering why? The main reasons is to avoid mildew growing on the inside. Some amount of condensation will always be present on the inside of waterproof breathable waders, simply because of how the fabric functions. The material used on breathable waders works in this way; there are thousands of tiny holes, that are too small for moisture (water) to fit through but are big enough for vapor or air to move through. This allows air to flow through, hence making them breathable, but keeps water from passing through. Because the human body naturally passes moisture out through the skin, a bit of condensation build up throughout the legs, feet, knees and on the ankles is normal. This is just a function of moisture escaping the body and being left on the inside of the breathable membrane as the warm air escapes out through the fabric and leaves moisture behind. If you’re interested we have more information about condensation here.

The bottom line is that mildew is not only gross, but it actually damages waterproof breathable fabrics and seam tape making them more likely to wear out and fail faster. So just hang your waders up in a warm well ventilated area and they will dry out completely and be ready for your next trip. We’ll leave you with these example photos below of what to avoid! The black spots throughout is all black mildew, doing it’s best to damage and ruin these waders.

Cheers!

Zipper care – 4 easy steps how to care for and clean your wader zippers

Take care of your zipper, and your zipper will take care of you.

From pocket zippers to waterproof zip front wader models, all of our fishing waders have multiple zippers that provide different levels of function. The pocket zippers keep things organized and in place, while the main waterproof zipper on the Primo Zip front wader allows easy in and out access. They all need a little care from time to time to keep them running smoothly and operating for the long run. Here are four easy steps for how to care for your zippers.

  1. Keep all debris such as dirt, sand, fishing line, clothing, bait goop, and salt crust out of the zipper teeth.
  2. Use a cleaner and lubricate regularly.
  3. Always store and pack fully unzipped. The exception to this is when hanging your zip front waders it is recommended to hang them fully zipped up. Packing them fully unzipped helps prevent damage.
  4. Never force a stuck zipper. Instead lubricate thoroughly and gently back off.

Notes on storage and transport of zip front wader models. We recommend storing and transport your waders fully unzipped, with the exception of hanging zip front waders fully zipped up. Never bend or fold your waders when zipped up as this can add stress and create a weak point in the zipper.  When packing for travel, fully unzip your waders and roll them from the feet up and try not to pack them at the bottom of your baggage with heavy items on top.

A final point about waterproof zip front models. Foreign matter caught in the zipper can result in damage which may not be covered under warranty. Keep it clean and never force the zipper. If the zipper sticks at all when zipping, stop immediately and gently unzip in the opposite direction if possible, and then clean the zipper thoroughly before using again. We recommend Zipper Cleaner and Lubricant and Zipper Lubricant Stick from Gearaid to get it sliding smoothly again.  Use the snap at the top to take stress off and keep it from pulling apart while wearing.  


How to repair pinholes or tears in breathable waders

finished patch on breathable fishing waders

Finding a leak and repairing your breathable waders

Use these instructions and photo examples below to find and repair pinholes, tears, or holes in your breathable waders.

Step 1:

If there is a visible tear or hole then skip this step and proceed to step 2.  To find a leak, first carefully visually inspect the area and see if you can see any tiny holes or tears. Often times you’ll be able to find the spot just by looking closely.  If there is no visible hole or tear, then the alcohol method works well to find it. To do this turn the waders inside out, and spray or rub a small amount of rubbing alcohol over the area you think is leaking. Then flip the waders back right side out and look for the wet spot. Any leaks will show as a damp spot on the outer side of the fabric. Mark this with masking tape or a marking pen, dry the waders and then move on to the repair. 

Step 2:

Usually a small tear or leak can be completely repaired with just a little Aquaseal. Once you locate the leak, the easiest repair is to coat one or both sides with Aquaseal. A tip for using Aquaseal is to heat the bottle just a bit in warm water, which makes it much easier to use. To spread it, use a flat squeegee (a piece of cardstock or a business card works well) to form a thin layer over the affected area. We recommend using some masking tape to mask off the area around the tear or pinhole to keep it contained to just the area around the tear.

For a durable repair using the material supplied in the repair kit, usually for a larger tear or rip, use a piece of the fabric supplied to cover the tear. Cut a piece of fabric to the relative size of the tear allowing it to overlap. Then Aquaseal over the tear, stick the fabric down and seal the edges of the fabric with Aquaseal. This will create a permanent patch. Before doing any Aquaseal repair mask off the area with some masking tape, scotch tape, or any tape to help keep the Aquaseal in a neat area over the repair. Make sure to remove the tape after 10-15 minutes while the Aquaseal is still wet. 

The seam tape that is included in the repair kit is heat activated. This is a bit more advanced, and there is potential for damage since you’ll be applying heat to an area of the fabric. For at home, an old iron set to medium high temp can work well to ‘iron on’ a bit of seam tape to the inside of the waders. This probably won’t be necessary and is not normally required. However this can seal the inside on a small tear, pinhole, or seam nicely when done correctly. This backing can also be done with gear repair tape like Tenacious tape.

Step 3:

Get back to fishing. 

Note: Also recommend carrying Aquaseal UV on trips. It cures within 20-30 seconds in direct or indirect sunlight (UV) and can save the day in a pinch.

Photo examples of patching a tear.

In these photo examples we will show you steps to locate and repair a tear in waterproof breathable wader fabric.

1 – 3. Photos showing the hole. This tear is visible on the exterior and interior. Photo 3 shows what the alcohol test looks like. For non visible pinholes it will just look like a wet spot.

tear in breathable waders
tear in breathable waders inside
tear in breathable waders alcohol test

4. Apply backing on the inside. In this photo we used heat sealed seam tape, essentially applied with a hand held iron. In place of seam tape you can use a gear repair tape like Tenacious tape, or skip this step altogether. If skipping, we recommend putting some regular tape on the inside over the hole to prevent Aquaseal from squeezing through in the next step.

Patching breathable fishing waders

5 & 6. Apply Aquaseal. We usually cut a small piece of cardboard stock from the packaging to apply. Apply Aquaseal and smooth over the hole, making sure it completely fills and covers the hole.

Aquaseal for patching waders

7. Measure and cut a piece of fabric from the supplied repair kit. Tenacious tape can be used in place of wader fabric in this step as well. Just be sure to cut the tape patch oversized enough so that there is at least 1/2 inch extra on all sides to stick to the fabric, and not over glue.

cut a patch to size

8. Apply a thin layer of Aquaseal to the backside of the fabric piece. Again use a small piece of cardboard or a business card as a tool.

9. Stick it down and let it dry. If the edges are lifting up you can use some masking tape to hold it down temporarily. So long as there isn’t a lot of extra glue coming out the edges the tape can be removed once it is dry.

applying patch to breathable fishing waders

10. To make a clean looking patch, surround the patch and any areas you don’t want to Aquaseal over with masking tape. Then apply Aquaseal around the edges of the patch. Be sure to remove the tape while the Aquseal is still wet. Otherwise it will be permanent. This step is completely optional.

masking off patch

11. The finished patch. This patch is very durable.

finished patch on breathable fishing waders

We thank you for your support

Did you know DRYFT is a small independent family owned business? The two owners, Nick and Sam, and their families run daily operations and oversee all aspects of the business. If you’ve ever reached out to us with questions you’ve likely talked to one of us. We hand pack each order ourselves, and take pride in the products we sell. We appreciate your business and support and would like to say thank you. We hope you enjoy the holiday season with your family and friends.

-Sam & Nick

DRYFT owners Nick (left) and Sam (right) enjoying some of the fishing bounty that Alaska has to offer.

Fly fishing for tiger musky; I love musky. I hate musky. Ok, I love musky again.

tiger musky fly fishing washngton - dryft

Fly fishing for musky: long hours of repetitive movements followed by brief intense action followed by jubliation or soul crushing disappointment. These fish are hard to catch but so worth the effort.

Fly fishing for tiger musky in Washington state

tiger musky fly fishing washngton - dryft

tiger musky fly fishing washngton - dryft
.

tiger musky fly fishing washngton - dryft
.

tiger musky fly fishing washngton - dryft
.

Fall PNW backcountry walk ‘n wade – Exploring new water

DRYFT S14 fishing waders

DRYFT S14 fishing waders

Fall fishing in the PNW backcountry has a lot to offer.

Getting remote and exploring streams and rivers in the mountain regions can pay off big. Recently Nick and Sam went out on a quick overnight mission to explore some new water.

Upon arriving to the area we’d be exploring we were greeted by multiple signs warning of an aggressive bear ransacking occupied campsites. “Camping not advised’ warned one of the signs. Good thing we forgot the bear spray at home.

Well in the end we survived the night without a bear attack. 🙂

Fishing turned out to be tough, but the scenery sure was easy on the eyes. This was a perfect way to step back and get grounded before the busy fall season picks up. Here are some photos from the trip.

PNW Backcountry photos

DRYFT S14 fishing waders - fall backcountry fishing DRYFT S14 fishing waders - fall backcountry fishing DRYFT S14 fishing waders - fall backcountry fishing DRYFT S14 fishing waders - fall backcountry fishing DRYFT BKCNTRY Waterproof backpack - fall backcountry fishing DRYFT S14 fishing waders - fall backcountry fishing DRYFT S14 fishing waders - fall backcountry fishing DRYFT S14 fishing waders - fall backcountry fishing